| Main features | Catalina 30 MkII Fin keel |
Model | Catalina 30 MkII |
Version | Fin keel |
Hull type | Monohull |
Category | Cruising sailboat |
Sailboat builder | Catalina Yachts |
Sailboat designer | |
Country | United States |
Construction | Hull and deck: GRP (glass reinforced polyester) |
First built hull | 1986 |
Last built hull | 1991 |
Appendages | Keel : fin without bulb |
Helm | Single helm wheel |
Rudder | Single spade rudder |
Unsinkable | No |
Trailerable | No |
| Main dimensions | Catalina 30 MkII Fin keel |
Hull length | 29’ 11”9.12 m |
Waterline length | 25’7.62 m |
Beam (width) | 10’ 10”3.3 m |
Draft | 5’ 2”1.6 m |
Light displacement (MLC) | 10201 lb4627 kg |
Ballast weight | 4200 lb1905 kg |
Ballast type | Lead |
| Rig and sails | Catalina 30 MkII Fin keel |
Upwind sail area | 446 ft²41.43 m² |
I iFore triangle height (from mast foot to fore stay top attachment) | 41’12.5 m |
J iFore triangle base (from mast foot to bottom of forestay) | 11’ 6”3.51 m |
P iMainsail hoist measurement (from tack to head) | 35’10.67 m |
E iMainsail foot measurement (from tack to clew) | 11’ 6”3.51 m |
Rigging type | Sloop Marconi masthead |
Mast configuration | Deck stepped mast |
Rotating spars | No |
Number of levels of spreaders | 1 |
Spreaders angle | 0 ° |
Spars construction | Aluminum spars |
Standing rigging | 1x19 strand wire continuous |
| Performances | Catalina 30 MkII Fin keel |
Upwind sail area to displacement iThe ratio sail area to displacement is obtained by dividing the sail area by the boat's displaced volume to the power two-thirds.The ratio sail area to displacement can be used to compare the relative sail plan of different sailboats no matter what their size. Upwind: under 18 the ratio indicates a cruise oriented sailboat with limited performances especially in light wind, while over 25 it indicates a fast sailboat. | 161 ft²/T14.92 m²/T |
Displacement-length ratio (DLR) iThe Displacement Length Ratio (DLR) is a figure that points out the boat's weight compared to its waterline length. The DLR is obtained by dividing the boat's displacement in tons by the cube of one one-hundredth of the waterline length (in feet).The DLR can be used to compare the relative mass of different sailboats no matter what their length: a DLR less than 180 is indicative of a really light sailboat (race boat made for planning), while a DLR greater than 300 is indicative of a heavy cruising sailboat. | 296 |
Ballast ratio iThe Ballast ratio is an indicator of stability; it is obtained by dividing the boat's displacement by the mass of the ballast. Since the stability depends also of the hull shapes and the position of the center of gravity, only the boats with similar ballast arrangements and hull shapes should be compared.The higher the ballast ratio is, the greater is the stability. | 41 % |
Critical hull speed iAs a ship moves in the water, it creates standing waves that oppose its movement. This effect increases dramatically the resistance when the boat reaches a speed-length ratio (speed-length ratio is the ratio between the speed in knots and the square root of the waterline length in feet) of about 1.2 (corresponding to a Froude Number of 0.35) . This very sharp rise in resistance, between speed-length ratio of 1.2 to 1.5, is insurmountable for heavy sailboats and so becomes an apparent barrier. This leads to the concept of "hull speed".The hull speed is obtained by multiplying the square root of the waterline length (in feet) by 1.34. | 6.70 knots |
| Auxiliary engine | Catalina 30 MkII Fin keel |
Engine(s) | 1 inboard engine |
| Accommodations and layout | Catalina 30 MkII Fin keel |
Cockpit | Closed aft cockpit |
Cabin(s) | 2 |
Berth(s) (min./max.) | 4 / 6 |
Head(s) | 1 |