Detailed sailboat specifications and datasheets since 2015
MetricSI (m)
Imperial & Metricboth
ImperialIMP (ft)

X-372 (Mast head rigging)

Main featuresX-372 Mast head rigging
Model
X-372
Version
Mast head rigging
Hull type
Monohull
Category
Cruiser-racer sailboat
Sailboat builder
X-Yachts
Sailboat designer
Country
Denmark
Construction
GRP (glass reinforced polyester):
Sandwich fiberglass polyester with galvanized steel frame
Number of hulls built
120
First built hull
1987
Last built hull
1992
Appendages
Keel : fin without bulb
Helm
Single tiller (helm wheel in option)
Rudder
Single spade rudder
Unsinkable
No
Trailerable
No
 
Main dimensionsX-372 Mast head rigging
Overall length
37’ 8”11.48 m
Hull length
36’ 4”11.05 m
Waterline length
29’ 6”9 m
Beam (width)
11’ 8”3.57 m
Draft
6’ 7”2 m
Light displacement (MLC)
11244 lb5100 kg
Ballast weight
4850 lb2200 kg
Ballast type
Cast iron / lead fin
 
Rig and sailsX-372 Mast head rigging
Upwind sail area
818 ft²76 m²
Downwind sail area
1419 ft²131.8 m²
Mainsail area
304 ft²28.2 m²
Genoa area
515 ft²47.8 m²
Solent area
343 ft²31.9 m²
Stormjib area
108 ft²10 m²
Symmetric spinnaker area
1115 ft²103.6 m²
Rigging type
Sloop Marconi masthead
Mast configuration
Keel stepped mast
Rotating spars
No
Number of levels of spreaders
2
Spreaders angle
0 °
Spars construction
Aluminum spars
 
PerformancesX-372 Mast head rigging
Upwind sail area to displacement
 iThe ratio sail area to displacement is obtained by dividing the sail area by the boat's displaced volume to the power two-thirds.

The ratio sail area to displacement can be used to compare the relative sail plan of different sailboats no matter what their size.

Upwind: under 18 the ratio indicates a cruise oriented sailboat with limited performances especially in light wind, while over 25 it indicates a fast sailboat.
276 ft²/T25.65 m²/T
Downwind sail area to displacement
 iThe ratio sail area to displacement is obtained by dividing the sail area by the boat's displaced volume to the power two-thirds.

The ratio sail area to displacement can be used to compare the relative sail plan of different sailboats no matter what their size.
479 ft²/T44.48 m²/T
Displacement-length ratio (DLR)
 iThe Displacement Length Ratio (DLR) is a figure that points out the boat's weight compared to its waterline length. The DLR is obtained by dividing the boat's displacement in tons by the cube of one one-hundredth of the waterline length (in feet).
The DLR can be used to compare the relative mass of different sailboats no matter what their length:

a DLR less than 180 is indicative of a really light sailboat (race boat made for planning), while a DLR greater than 300 is indicative of a heavy cruising sailboat.
198
Ballast ratio
 iThe Ballast ratio is an indicator of stability; it is obtained by dividing the boat's displacement by the mass of the ballast. Since the stability depends also of the hull shapes and the position of the center of gravity, only the boats with similar ballast arrangements and hull shapes should be compared.

The higher the ballast ratio is, the greater is the stability.
43 %
Critical hull speed
 iAs a ship moves in the water, it creates standing waves that oppose its movement. This effect increases dramatically the resistance when the boat reaches a speed-length ratio (speed-length ratio is the ratio between the speed in knots and the square root of the waterline length in feet) of about 1.2 (corresponding to a Froude Number of 0.35) . This very sharp rise in resistance, between speed-length ratio of 1.2 to 1.5, is insurmountable for heavy sailboats and so becomes an apparent barrier. This leads to the concept of "hull speed".
The hull speed is obtained by multiplying the square root of the waterline length (in feet) by 1.34.
7.28 knots
 
Auxiliary engineX-372 Mast head rigging
Engine(s)
1 inboard engine
Engine(s) power
28 HP
Fuel type
Diesel
 
Accommodations and layoutX-372 Mast head rigging
Cockpit
Open aft cockpit
Cabin(s)
2
Berth(s) (min./max.)
4 / 6
Head(s)
1
Maximum headroom
6’ 2”1.9 m
 
Boat-Specs.com uses cookies to improve user experience. By using our website you consent to all cookies in accordance with our Cookie Policy.

Read more